- #R3 QSX QUICKSHIFT INSTRUCTIONS HOW TO#
- #R3 QSX QUICKSHIFT INSTRUCTIONS INSTALL#
- #R3 QSX QUICKSHIFT INSTRUCTIONS FULL#
- #R3 QSX QUICKSHIFT INSTRUCTIONS ANDROID#
- #R3 QSX QUICKSHIFT INSTRUCTIONS BLUETOOTH#
#R3 QSX QUICKSHIFT INSTRUCTIONS BLUETOOTH#
The working range is affected by the module’s position and the phone’s Bluetooth capabilities. The QSX harness has a module integrated with which the ECM does not detect the ignition cut and the FI light will not come on. Please contact your distributor to arrange an exchange. If you see the QSX listed but you installed a QSH harness, that is the problem. Please check our Product Advisor to see if we list a QSH or QSX harness for your bike. When I do a quickshift at high RPM on my Suzuki, the FI light comes on
#R3 QSX QUICKSHIFT INSTRUCTIONS FULL#
at partial to full throttle, well above idle speed.ġ3. › Make sure you do clutchless upshifts only during acceleration, i.e. There are times the shifts are really smooth, at other times it’s rough, i.e. Increase the cut-off times by 5-10ms and try again.ġ2. If you change the gear slowly, you may hit false neutral or you can’t make the shift at all. Adjust the shift lever position if necessary to ensure effortless and complete shift movement with your foot. Be sure you always do quick, confident and complete shift movements with your foot, until the lever stops. Sometimes I hit a false neutral, or the gearbox stays in the same gear › Keep in mind that the cut-off is disabled under the First RPM value.ġ1. › If the Cut-off test works, make sure the iQSE module is not disabled (see Bypass mode) in the app. Otherwise, disconnect the module, connect the supplied 4-pole Jumper-plug and contact us for advice. This proves the module’s output is working. The engine should stop momentarily (or even completely) when you push the Cut-off test button. Under RPM Settings, press the test button and see if the engine stops for a short time or not. Open the iQSE app and connect to the module. Most likely your side stand switch is failing or has a poor connection. At high RPM (or at high speed) sometimes the engine shuts off › If the problem persists, activate the Noise filtering option in the app.ĩ. › Be sure you are not resting your foot on the shift lever. Refer to the help in the app under Sensor setup. › Make sure you are running the most current version of the iQSE app. › Be sure the sensor is installed properly. At high RPM (or at high speed) I get unwanted ignition cuts
#R3 QSX QUICKSHIFT INSTRUCTIONS INSTALL#
If this test is OK, install the sensor and be sure to follow the steps in the most current version of the Sensor install guide.Ĩ. You should be able to generate a signal higher than 30% with your fingers. › Squeeze the sensor with your thumb and index fingers rapidly and hard. › Under Sensor setup, make sure the “QSE sensor” is selected and the “Noise filtering” is Inactive. › Dismount the sensor but leave the 2-pole sensor plug connected
#R3 QSX QUICKSHIFT INSTRUCTIONS HOW TO#
How to check whether the QSE Sensor is working fine? Use a good chassis ground bolt, preferably on the gearbox, or you may use the battery negative terminal.ħ. If the starter motor is spinning but the engine does not start with the iQSE (although it starts fine with the jumper plug), most likely the QSH black wire terminal has poor ground connection. On some bikes, the engine has to be running, otherwise the module is not powered. Make sure you have the engine stop switch in RUN position and the ignition key switched ON. Disconnect ONE bike connector at a time, and connect ONE pair of the QSH connectors in-line with the coil and bike plug, then proceed with the next. The engine hardly starts and I get a very rough idle › The QSH harness is damaged or not suitable for your bikeĤ. › A connector pin does not make contact (bent or loose) from the fuel tank) may not be reconnected The engine does not start, even when using the Jumper plug
#R3 QSX QUICKSHIFT INSTRUCTIONS ANDROID#
This includes models from iPhone 4s to 6s and from iPad 2 to iPad Pro.Īll phones and tablets running Android 2.3 or later are supported.ģ. › Make sure you are running the most current version of the iQSE app.Īll iOS devices running iOS 8.1 or later are supported. › Move the unit to a different spot, farther from the ECU.
› Make sure the iQSE LED is ON (solid red or solid green). If you see “QSE” you have the first generation module and it’s not compatible with iOS devices. › Make sure the label on the unit is “iQSE”. I can not establish a connection to the module Use our Product Advisor to find the part numbers suitable for your bike.Ģ. This document is a guide to help troubleshoot problems that might arise during the installation, setup or normal usage of the HealTech QuickShifter easy product.īefore starting the installation, make sure you got the correct parts.
0 kommentar(er)
